Announcement

Collapse
No announcement yet.

Setting up Edcast server on WINMAP

Collapse
X
  • Filter
  • Time
  • Show
Clear All
new posts

  • Setting up Edcast server on WINMAP

    Step 1 - Install Edcast Standalone

    Download Edcast Standalone software and install it. This is a free application that can broadcast live audio to Icecast or Shoutcast servers. Edcast doesn’t require any other software to operate (hence the name ‘Standalone’), and is ideal for 24/7 live streaming environments such as streaming an AM/FM station over the internet.


    Step 2 - Install the LAME MP3 Encoder

    • (1, 2) Attachments below and choose “Save As… or Click on”


    1.jpg


    Navigate to ‘C:\ Program Files \ edcast’ and click ‘Save’.
    It is VERY important that you save this file inside the actual Edcast program folder.

    22.jpg


    Step 3 - Start Edcast Standalone and configure the encoder

    • (3) Click the ‘Add Encoder’ button
    • (4) Right-click the new encoder that appears below it
    • (5) Choose ‘Configure’ from the menu that appears


    3.jpg

    In the ‘Basic Settings’ section, set up the encoder.

    • (1) Click her
    • (bitrate) Enter your chosen bitrate - this must be equal or lower than the rate you purchased.
    • (samplerate) Enter your samplerate - Enter 44100 for bitrates above 96, or 22050 for streams below 96.
    • (channels) Number of channels - Enter 2 for bitrates above 48, choose 1 for bitrates below 48.
    • (2) Select the ‘MP3 Lame’ encoder but i was select oggvorbis
    • (3) Select ‘Icecast2’ for Icecast server, or ‘Shoutcast’ for Shoutcast server. (looking for streaming with shoutcast server )
    • (4) Enter the host name of your server or IP of you VPS.
    • (5) Enter the port number of your server. LIKE : 8080 . 8001. 7750......
    • (6) Enter the DJ or Admin password of your server.
    • (7) (Icecast2 only) Enter the mount point - this will usually be /stream by default for Fast Serv Icecast2 servers.
    • (8) not impotant, you can add some information for stream descriptions
    • (9) not important
    • (10) Click ok




    4.jpg

    • (8) (9) In the ‘YP Settings’ section, enter your station details.
    • (10) Click ‘OK’


    5.jpg


    Step 5 - Start encoding

    • (15) Tick the ‘AutoReconnect’ box
    • (16) Hilite the new encoder, then click the ‘Connect’ button
    • You should see information about the encoder status in the ‘Transfer Rate’ column. If it’s working properly, a numeric value will appear indicating the transmission speed.





    thats's all !!!
    Enjoy!!!
    Attached Files
    ------------------------------------------

    1
    D
    o Not Send Me PM For Support
    .
    2 Do Not Send Me PM For ASK Test.
    3 Ask Your Question On The Forum.

    ------------------------------------------
    My Email is :
    mspauljayo[at]gmail.com
    ------------------------------------------



  • #2
    Step 5 - Start encoding

    • (15) Tick the ‘AutoReconnect’ box
    • (16) Hilite the new encoder, then click the ‘Connect’ button
    • You should see information about the encoder status in the ‘Transfer Rate’ column. If it’s working properly, a numeric value will appear indicating the transmission speed.


    A3.jpg
    ------------------------------------------

    1
    D
    o Not Send Me PM For Support
    .
    2 Do Not Send Me PM For ASK Test.
    3 Ask Your Question On The Forum.

    ------------------------------------------
    My Email is :
    mspauljayo[at]gmail.com
    ------------------------------------------


    Comment

    Working...
    X